spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 2.0x1.25mm smd chip led lamp part number: APHBM2012LSURKCGKC hyper red green features z 2.0mmx1.25mm smd led, 0.45mm max. thickness. z bi -color, low power consumption. z wide viewing angle. z ideal for backlight and indicator. z package : 2000pcs / reel. z moisture sensitivity level : level 3. z low current if=2ma operating. z rohs compliant. descriptions z the hyper red source color devices are made with algainp on gaas s ubstrate light emitting diode. z the green source color devices are made with algainp on gaas substrate light emitting diode. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1(0.004") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications.
spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1. wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4. excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradat ion or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (mcd) [2] @ 2ma v iewing angle [1] min. typ. 2 1/2 APHBM2012LSURKCGKC hyper red (algainp) water clear 10 20 120 *2 *10 1.2 2 *1.2 *2 green (algainp) symbol parameter emitting color typ. max. units test conditions peak peak wavelength hyper red green 645 574 nm i f =2ma d [1] dominant wavelength hyper red green 630 570 nm i f =2ma ? 1/2 spectral line half-width hyper red green 28 20 nm i f =2ma c capacitance hyper red green 35 15 pf v f =0v;f=1mhz v f [2] forward voltage hyper red green 1.75 1.9 2.1 2.1 v i f =2ma i r reverse current hyper red green 10 10 ua v r = 5v min. 1.5 1.5 parameter hyper red green units power dissipation 63 63 mw dc forward current 30 30 ma peak forward current [1] 185 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c
spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 APHBM2012LSURKCGKC hyper red
spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 green
spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 APHBM2012LSURKCGKC reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsag8266 rev no: v.2a date: aug/01/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203006075 packing & label specifications APHBM2012LSURKCGKC terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
